Zepro’s slider model ZS/ZSS is specifically conceived for installation under trucks. Lifting capacity of 1500kg, 2000kg and 2500kg can be offered for these models.

This is essentially a normal tail lift which is attached to an in/out slider system which allows the lift to be moved from its stowed position to the working position and back again. In order to take as little overhang space in the stowed position the platform folds. The sliding system has a hydraulic motor driving 2 sprockets which rotate and run under the slide profiles guided by simple, sturdy chains. Hence the driving force is spaced out to two points wide of the centre-line.

This enables a smooth in/out movement avoiding the uneven ‘chest of drawers’ effect associated with centrally positioned cylinders. The profiles have holed plates to allow a simple bolt-on installation onto channel profile truck frames.

Single folding platforms can be ordered in variouslengths and widths. The length of the first part affects the overhang that the lift requires under the truck and the length of the folding part has to be adapted to the installation situation eg. if it is too long, there may not be space under the body/chassis for it to foldout. For 1500kg and 2000kg models both parts of the folding platform are made of aluminium. This gives low weight and makes the manual folding operation (which is also spring-assisted) less demanding from and to the stowed position.

For the heavy dutymodel, the 2500kg, we offer steel first part only due to the particularly high working loads required. The folding part is of aluminium.

Standard widths are 2350mm, 2450 mm and 2530 mm. The load centre on the platform is 750 mm.

The range is split into two sub-groups the ZS and ZSS. The difference being the overhang required for positioning of the lift. In general ZSS is more popular for insulated bodies with greater distancebetween the chassis and the floor. The ZS is more often chosen when overhang is limited. See our datasheets for detailed geometric information of the various models.

Both the ZS and ZSS are available with 3 different arm lengths allowing lifting heights up to 1725mm.

ZEPRO has always offered hydraulic units positioned inside of the support frame. This is the best way of protecting the critical components which drive the hydraulics. The sliders adopt the same design philosophy and hence have a low noise profile and renowned reliability due to very low frequency of component failure.

There are however a great many accessories which are compatible with this model. Many of these can either be installed at the factory or after the lift is already in service. Read more in the accessories section.

As with other ZEPRO models, if 5 units or more are ordered you may choose special painting in the RAL colour of your choice. In the case of this model the platform and the main frame components which are the most visible are painted in the special colour.

Техническая информация ZEPRO ZS 25



 Задать вопрос по крану ZEPRO ZS 25




  (+37517) 347-06-06
  (+37529) 662-26-61
  (+37529) 346-06-06
  Этот адрес электронной почты защищён от спам-ботов. У вас должен быть включен JavaScript для просмотра.
  Пн-Пт с 09:00 до 17:00
  Минск, Игуменский тракт, д.20, офис 2Н




Hiab — мировой лидер в области оборудования для дорожных погрузо-разгрузочных операций. Наша первоочередная задача — удовлетворение требований клиентов. Ассортимент нашей продукции включает краны-манипуляторы HIAB, краны для лесозаготовительных работ и переработки JONSERED, краны для лесозаготовительных работ LOGLIFT, навесные вилочные погрузчики MOFFETT и сменные крюковые погрузчики MULTILIFT, а также гидроборта DEL, WALTCO и ZEPRO. Компания Hiab входит в состав Cargotec Corporation.